350vip浦京集团(中国)有限公司

      巴可（Barco）D2大屏高亮IU(R764739)是巴可控制室系统基于创新的模块化方法设计投影模块，分离投影单元和发光单元，理念独特，投影设备易于维护、图像质量更加出色，显示清晰锐利的图像。光学调光器保证整个屏幕墙都具有相同亮度和对比度，让屏幕长期保持恒定性能。

 • 模块化投影单元

 • 包括各种大功率电源

 • 有源系统减少亮度公差

 • 集成冗余灯泡系统

 • 双灯冗余驱动器

 • 易于更换灯泡

 • 更换后无需重新进行集合校准

   Barco OverView D2 large screen highlighted IU(R 764739) is a new modular system of the Barco control room system to design projection modules, separation of projection and luminescence units, unique concept, projection equipment easy to maintain, better image quality, display clear and sharp images. The optical dimmer ensures the same brightness and contrast throughout the screen wall, keeping the screen constant over the long term.

 • Modular projection module

 • Includes all high power sources

 • Active systems reduce brightness tolerance

 • Integration of redundant light bulb systems

 • Double light redundant drives

 • Easy to change light bulbs

 • No need to recalibrate after replacement

明亮显示

一个UHP投影灯提供高光通量，它通过照明系统以很高的效率传输。(UHP是飞利浦电子Philips Electronics N.V.的商标)。根据需求，照明单元可以配用180W投影灯

双灯系统

投影机具有一个双灯系统，而且能够以三种工作模式运行：热待机模式、冷待机模式以及自动切换模式。在热待机模式下，两个投影灯均通电发光。如果其中一个投影灯出现故障，系统将立即切换至另一个投影灯的光输出来为光学设备照明，而且，它对所显示的信息无显著影响：既未损失信息，也未影响质量。切换时间约为半秒钟。

在冷待机模式下，仅在活动投影灯出现故障时才会打开第二个投影灯。由于第二个投影灯需要数分钟时间来达到一个稳定的工作温度，在开始时显示屏的亮度将会降低。不过，仍可以几乎没有任何中断地提供信息内容。

自动切换模式是冷待机模式的特例：投影灯轮流处于活动状态：在一个已定义周期之后，使用其他投影灯来为光路照明。由于该投影灯提前打开了数分钟，所以几乎不会注意到第二个投影灯已经接替工作。循环时间可以设定在12 小时与500 小时之间。

光源

灯冗余：配备冗余电源的冷待机或热待机

通过自动适应灯故障实现自动灯切换

更换灯：可热更换缺陷灯，且无图像损失

灯开关：通过动态反馈亮度和色彩，将视频墙重新调整至等效性能

灯开关时间：少于 1.5 秒

I型灯：智能灯包含 AO 灯的使用寿命信息和光谱

Bright Display

A UHP projection lamp provides a high luminous flux, which is transmitted efficiently through the lighting system. (UHP is the trademark of Philips Electronics N.V.). The lighting unit can be fitted with 180W projection lamps as required

Double Light System

The projector has a double light system and can operate in three modes: hot standby mode, cold standby mode and automatic switching mode. In the hot standby mode, both projection lamps are electrified. If one of the projection lamps fails, the system immediately switches to another projection lamp for optical lighting, and it has no significant effect on the information shown: neither lost information nor quality. Switching time is about half a second.

In standby mode, the second projection lamp is turned on only when the active projection lamp fails. Since the second projection lamp takes several minutes to reach a stable working temperature, the brightness of the screen will decrease at the beginning. However, the content of information can still be provided almost without interruption.

Automatic switching mode is a special case of standby mode: the projection lamp rotates in active state: after a defined period, other projection lamps are used to light the light path. Since the projection lamp was turned on a few minutes in advance, it was hardly noticed that the second projection lamp had taken over. The cycle time can be set between 12 and 500 hours.

light source

Light Redundancy: Cold or hot standby with redundant power supply

Automatic Light Switching through Automatic Adaptive Light Fault

Replacement of lamps: hot replacement of defective lamps without loss of image

Lamp switch: Readjust video wall to equivalent performance through dynamic feedback brightness and color

Light switching time: less than 1.5 seconds

Type I Lamp: Smart Lamp contains the service life information and spectrum of AO Lamp

灯泡：                 灯泡使用寿命（灯泡制造商规格 @ IEC 61947-1 测试条件）：

                       2x180瓦UHP™投影灯，标称寿命2x6000小时 

灯泡模式：             热待机、冷待机和自动切换模式

灯泡切换时间：         灯泡切换后：0,5 秒 -灯泡故障后：1,5 秒

                       执待机－灯泡切换后 0.5 秒内图像达到 50% 亮度

交流电源：             100-240V

主频：                 60/50 Hz

电流：                 冷待机   2.1A - 0.95A   热待机   3.5A - 1.5A

功耗：                 冷待机   180W灯 <335W  热待机   180W灯 <550W